Tel: +8613864314350

E-mail: andy@chinafluoropolymer.com

You are here: Home > Product > FEP > FEP Resin
FEP Extrusion Pellet

FEP Extrusion Pellet

Specification of FEP Extrusion Pellet DS618
1:Appearance: Translucent particles
2:Melting Index:12-28 g/10min
3:Tensile Strength 16Mpa Min
4:Melting Point :256+/-106

Send InquiryChat Now
Product Details

Quality Specification of  FEP Extrusion Pellet  DS618


Item

Unit

DS618



A

B

C

D

Appearance

Translucent particles,without impurities such as metal debris and sand,containing visible black particles percentage point less than 2%





Melting Index

g/10min

16.1-20

20.1-24

24.1-28

12.1-16

Tensile strength≥

Mpa

20

18

16

20

Elongation at break ≥

%

300

270

250

300

Relative Gravity


2.14-2.17




Melting point

°C

265±106




Dielectric constant


2.15










Dissipation Factor


7.0x10




Volatile,≤

%

0.1




Heat stress Cracking Resistance







Physical Properties of FEP Extrusion Pellet DS618

 

    There is no feasible method to determine the molecular weight of FEP Extrusion Pellet. But the melt viscosity of FEP Extrusion Pellet at 380 ℃ is lower than that of PTFE Resin (103-104Pa. S). It can be seen that the molecular weight of FEP Extrusion Pellet is much lower than that of PTFE. The melting point of FEP Extrusion Pellet varies with the composition of the copolymer. The melting point of FEP Extrusion Pellet decreases with the increase of hexafluoropropylene content. According to the results obtained by differential thermal analysis, the melting point of domestic FEP Extrusion Pellet is between 250 ℃ and 270 ℃, which is lower than that of PTFE Resin. FEP Extrusion Pellet is a kind of crystalline polymer, and its crystallinity is lower than that of PTFE. When the melt of FEP Extrusion Pellet slowly cools to the temperature below the melting point of the crystal, the macro molecule recrystallizes and the crystallinity is between 50% and 60%; when the melt is cooled rapidly by quenching, the crystallinity is small. The crystal structure of FEP Extrusion Pellet in the range of 40% to 50% is spherulite and varies with resin, molding temperature and heat treatment.

 

Electrical Insulation Properties of  FEP Extrusion Pellet DS618


    The electrical insulation of FEP Extrusion Pellet very similar to that of PTFE. Its dielectric coefficient from deep cold to the highest operating temperature, from 50Hz to 1010Hz UHF wide range almost unchanged, and very low, only about 2. 1. The dielectric loss angle tangent varies slightly with frequency, but not with temperature. The volume resistivity of FEP Extrusion Pellet resin is very high, which is generally greater than 1015m, and it has little change with temperature and is not affected by water and moisture. The breakdown field with arc resistance greater than 165s.F46 increases with the decrease of thickness. When the thickness is greater than 1mm, the breakdown field strength is above 30KV/mm, but does not change with the change of temperature.

 

Thermal Properties of FEP Extrusion Pellet DS618


    The heat resistance of FEP Extrusion Pellet resin is second only to that of PTFE, and can be used continuously in the temperature range of-85 ~ 200 ℃. Even at the limit of -200 ℃ and 260 ℃, the properties of FEP Extrusion Pellet do not deteriorate and can be used for a short time. The thermal decomposition temperature of FEP Extrusion Pellet is higher than the melting point temperature. The decomposition products are mainly tetrafluoroethylene and hexafluoropropylene. Due to the fact that the isobaric groups usually carried by FEP Extrusion Pellet molecules also decompose at temperatures above the melting point, proper ventilation must also be taken into account in processing above 300 ℃. FEP Extrusion Pellet is fairly stable below the melting point temperature. But the mechanical strength loss is larger at 200 ℃. The decrease of melt viscosity and the thermal decomposition of the copolymers can be analyzed by increasing the melting index. FEP Extrusion Pellet is still not completely hard and brittle at -250 ℃, and still has a very small elongation and a certain flexural flexibility, which is even better than PTFE. Than any other type of plastic.


The Wire and Cable Insulation Layer of FEP Extrusion Pellet DS618


FEP Extrusion Pellet for wire and cable application.jpg 


Hot Tags: fep extrusion pellet, China, suppliers, manufacturers, factory, buy, price
Related Products
Inquiry